Friday, June 3, 2011
Changing spark plugs on a 99 Cad Catera?
I need help understanding how to change the spark plugs on a 99 Cad Catera. Just lifting the hood is no help. It appears the wires and plugs are covered up somehow. Please assist if you can. I want to avoid taking it to a dealership if I can.Changing spark plugs on a 99 Cad Catera?The spark plugs are located under the upper plenum on this vehicle. When you open the hood there is a large plastic cover to be removed, the upper plenum is an aluminum item typically attached by 10 to 12 bolts. Once the plenum is removed you will have access to the spark plugs. The spark plugs are platinum and expensive. It is typical to only have to replace them after 100,000 miles. If you have less you may be able to have the Fuel(induction)system service that will remove the carbon build up. Not to sound degrading but I would leave it to a professional mechanic on this ride.Changing spark plugs on a 99 Cad Catera?Rh side:Relieve the fuel system pressure.Disconnect the fuel supply and return hoses from the intake manifold.Move heater hoses. Unplug electrical connection @ coil pack.Remove the coil pack retainer bolts. Remove Coil pack. Note: Gm uses a special tool in order to avoid damaging the coil pack. You can fabricate a similar device.Lh side more straight forward.Changing spark plugs on a 99 Cad Catera?You have to take the plastic cover off the engine.May also have to remove the upper intake plenum to reach some of them.Car is not very popular so I'm not sure if it is coil over plug or not.Hopefully a GM expert will chime in.Changing spark plugs on a 99 Cad Catera?look and see if you can pull the front tire and the lowwer part of the inner fender then you should be able to get to the spark plugs the is what i do to my truck 2003 frod you can bye the replacsement pins to put the inner fender back on cheap
How do you fix a fuel injected car that has gas flooded spark plugs and wont turn on?
I have a 97 Nissan Altima GXE. It idled pretty rough for about two months until one day it turned off on me and didn't want to turn on no more. I changed the fuel filter, Fuel pressure regulator, and checked the gas pump and it pumps fine. I took the spark plugs out and they were soaked in gasoline. when i crank the engine to try and turn it on it just smells like gas. What could be the problem and solution?How do you fix a fuel injected car that has gas flooded spark plugs and wont turn on?Nissan has always had a problem with their cars flooding. I don't know why but usually just changing the plugs helps. Tsb advises customers to start car with accelerator held halfway down. They also have a redesigned starter that makes the engine turn faster when cranking. If you continue to have the problem it maybe from a different source like an injector leaking or fuel pressure may be too high. pull the vacuum line off of regulator and make sure that is not leaking also.How do you fix a fuel injected car that has gas flooded spark plugs and wont turn on?what plugs do u use ive used new plugs did same thing so i bought cheap ones like champions they burn hot try thatcheapest web hosting myspace code
After how many miles should u change your spark plugs? Iridium plugs last 100k miles?
I often get different answers as to how many miles your spark plugs are good for. I keep hearing that the iridium plugs last 100k miles but this seems a lil hard to believe, how true is that claim?After how many miles should u change your spark plugs? Iridium plugs last 100k miles?are they gaped properly thats all you need to knowAfter how many miles should u change your spark plugs? Iridium plugs last 100k miles?The plugs will be fine the problem we find is a lot of the time the spark plug wont come out. I suggest to replace at 60k just for that reason, and have anti-seize on the threads and then dielectric grease to the spark plug boot to keep moisture and water out, also ads to boot removal next time.After how many miles should u change your spark plugs? Iridium plugs last 100k miles?It depends on the motor and im not sure about iridium plugs but Platinum plugs have been around for years....I have a 1999 suburban that came with Platinum plugs, GM recommends replacing them at 100k........I have 151,000 on them....no misfires, but they probably dont look too pretty : )After how many miles should u change your spark plugs? Iridium plugs last 100k miles?40,000 to 50,000 miles. Before you buy Iridium plugs ask for the 100,000 mile warranty.
Do you have to pull the head on a 2004 Ford Taurus to change the spark plugs?
I have changed the fuel filter %26amp; it was full of rust. This stopped the sputtering at low speed 4 about a week. Think it probably needs changed again. While I am doing this for my friend I was going to change the spark plugs. I don't have access to the car right now it is in another state, %26amp; before I buy spark plugs I was wondering if anyone could tell me how hard they are to change.Do you have to pull the head on a 2004 Ford Taurus to change the spark plugs?No you do not have to take the head off.
They are fairly easy to change also.Do you have to pull the head on a 2004 Ford Taurus to change the spark plugs?Typical V6 FWD vehicle - the back plugs are somewhat of a hassle but not anywhere near as bad as some vehicles. You shouldn't have any problems if you've got access to some decent tools.Do you have to pull the head on a 2004 Ford Taurus to change the spark plugs?u shud b able to do them with no probDo you have to pull the head on a 2004 Ford Taurus to change the spark plugs?dont know the F/T but ford v6plugs arnt that bad the best things to do it with is a good make3/8 drive socket %26amp; extensions you will have more room to work with 3/8 than 1/2. get an assortment of lengths of extensions.Do you have to pull the head on a 2004 Ford Taurus to change the spark plugs?The best way to change plugs in this is to pull the right side windshield wiper box . It takes 3 bolts that are 7/32 of inch and 3 clips . This makes it easier to get to back plugs . I do a lot of Taurus repairs and this is the best way to get your hands back there . If it is a DOHC motor you have to pull the upper intake if it wraps over the plugs . Have not changed a 2004 DOHC so I am not sure but on the 2001 you have to . Good luck and this is about a 2 hour job taking your time less on the 12 valve Vulcan motor . Do not get frustrated it isn't all that bad .Do you have to pull the head on a 2004 Ford Taurus to change the spark plugs?No need to remove head, the back cylinders are a bit of a pain to remove and replace plugs in , but straightforward job. Change that fuel filter also, it will always help, if the last one was plugged you can be sure it will be doing it again.
They are fairly easy to change also.Do you have to pull the head on a 2004 Ford Taurus to change the spark plugs?Typical V6 FWD vehicle - the back plugs are somewhat of a hassle but not anywhere near as bad as some vehicles. You shouldn't have any problems if you've got access to some decent tools.Do you have to pull the head on a 2004 Ford Taurus to change the spark plugs?u shud b able to do them with no probDo you have to pull the head on a 2004 Ford Taurus to change the spark plugs?dont know the F/T but ford v6plugs arnt that bad the best things to do it with is a good make3/8 drive socket %26amp; extensions you will have more room to work with 3/8 than 1/2. get an assortment of lengths of extensions.Do you have to pull the head on a 2004 Ford Taurus to change the spark plugs?The best way to change plugs in this is to pull the right side windshield wiper box . It takes 3 bolts that are 7/32 of inch and 3 clips . This makes it easier to get to back plugs . I do a lot of Taurus repairs and this is the best way to get your hands back there . If it is a DOHC motor you have to pull the upper intake if it wraps over the plugs . Have not changed a 2004 DOHC so I am not sure but on the 2001 you have to . Good luck and this is about a 2 hour job taking your time less on the 12 valve Vulcan motor . Do not get frustrated it isn't all that bad .Do you have to pull the head on a 2004 Ford Taurus to change the spark plugs?No need to remove head, the back cylinders are a bit of a pain to remove and replace plugs in , but straightforward job. Change that fuel filter also, it will always help, if the last one was plugged you can be sure it will be doing it again.
How do i know that i would need to change my spark plugs?
what are some signs that i would need to have my spark plugs changed without actually getting under the hood and looking at them?How do i know that i would need to change my spark plugs?IF it's been awhile or if the MPG are going down and the car just doesnt seem very strong.How do i know that i would need to change my spark plugs?You should change them about every 40,000 miles... I know the dealers claim you can go 100,000 without changing them but at that point they are in real bad shape and REALLY tough to get out! If your gas mileage goes down, hard starting, or idle gets a bit shaky that is a sign as well.How do i know that i would need to change my spark plugs?I would just pull 1 out and look at it, you don't have to check everyone. If its been over 20,000 miles, they may be due anywayHow do i know that i would need to change my spark plugs?your engine seems like it running hard i had one that came out and it hit the top of the hood everytime I drove.. ,, bad gas mileage.. it could be several things.How do i know that i would need to change my spark plugs?black smoke from the pipe and the engine is running realy rough like just not normal. also just pull one out, the way it looks should tell you if you need new onesHow do i know that i would need to change my spark plugs?hard to start.....poor running....old age.....high milage.
How much to change spark plugs?
I have a 1989 toyota celica st and I am looking to put it platinum spark plugs to make it last longer. Do I have to get new wires too? How much would it be for just these two?How much to change spark plugs?platinum spark plugs can range in price anywhere from 2 dollars a piece to 8.. personally the brand u choose as your replacement would be the same as the wires.. yes the spark plugs and wires should be replaced at the same time to be able to adjust and operate the same as they wear as the years go by.. same as replacing oil filter along with new oil.. your probably looking anywhere in the range of 30 to 120 depending on how much your wanting to spendHow much to change spark plugs?plugs'll probly be $20 and wires'll probly be another $20How much to change spark plugs?go with iridium plugs, ngk makes them they are better. you do not have to replace your wires. make sure the plugs are gapped correctly.the ngk plugs are about 14-20 a plug. but worth it on the small amount of increased fuel economy. i didn't change the wires on my trans am.if you can do it yourself or ask some one to do it. you will get ripped off almost anywhere. i got quoted $285 to do the plugs in my trans am. that wasn't even counting the price of the plugs.How much to change spark plugs?If you don't have any miss firing or rough idle I wouldn't worry about the plug wires just change the plugs but use some anti seize on the threads of the plugs.This keeps them from seizing in the threads in the head of the engine.But make sure you gap the plugs before installing them.And make sure of the torque when putting them in and not to over tightening them because aluminum heads with spark plug holes will strip out them threads.Use a torque wrench if you don't have one borrow one from some body if you can't buy one from a parts store and ask what the torque should be on the plugs.How much to change spark plugs?I put Bosch twin electrode platinums in my Corolla 6 years ago and they're still good. I've ,since then , driven to Canada, Disneyland in Orange Co, Keystone Colorado and Vail Colorado, plus daily commute in the SanFrancisco Bay Area. I can talk about 60,000 miles on a set of platinum plugs and the original plug wires. Invest $10- $15 on those spark plugs and don't worry for the next 6 years at least.How much to change spark plugs?If you haven't replaced the ignition wires, cap and rotor with Denso or NGK parts within the past 50,000 miles you'd better add that to the %26quot;to do%26quot; list along with Denso or NGK platinum or longer lasting iridium spark plugs. Do not attempt to second-guess or re-gap iridium spark plugs. The center electrode is so small and hard it will spall off or break if you attempt to do so.
Can anyone tell me how I'm suppose to change the back spark plugs on a 98 pontiac transport?
The back spark plugs you can't reach with your hands can anyone tell me how to get to them.Can anyone tell me how I'm suppose to change the back spark plugs on a 98 pontiac transport?Most people take the bolts off the motor mounts that go to the top radiator support and use a small tie down strap and roll the engine forward.Can anyone tell me how I'm suppose to change the back spark plugs on a 98 pontiac transport?dont know about your car, but sometimes you have to access some plugs from the wheel well.Where to get comforters to day beds find remote key bmw logo
How and where do I change spark plugs on a 2001 Cadillac Deville?
My car was shaking after driving for awhile and someone told me that I had some cheap spark plugs in there. When I decided to change the spark plugs myself for the 1st time, I couldnt locate them. Can someone point me in the right direction? ThanksHow and where do I change spark plugs on a 2001 Cadillac Deville?you dont even know whats wrong...some guy told you? take it to a mechanic.
How do you change the spark plugs on a 1999 Lexus ES300?
I have a 1999 Lexus ES300 and i was wondering how to change the back spark plugs on it? Also i was wondering on how to change the spark plug wires? If there are any websites which have pictures please post them. I went to a mechanic and they told me that it would be around 150 to do the job. ThanksHow do you change the spark plugs on a 1999 Lexus ES300?The mechanic's price is too much, you can easily change the spark plugs by having a spark plug remover. Instead of paying 150, use this to buy yourself a spark plug remover. If you wish to change the wires, simply pull the black rounded terminals and they come out easily. You must change all four spark plugs to ensure smooth combustion on all four cylinders. Changing new spark plugs will only require 20-30 minutes.
Do we need to use the torque wrench to tight the spark plugs?
hello folks..
its regarding my 01 max and i have never changed the spark plugs on my car by myself, but i did changed the coils so i know how to get to the plugs etc, my question is..do i need to buy a torque wrench to tight the plugs or i can just use the rachet and hand tight them? please help me cuz i am on the way of getting this done today.Do we need to use the torque wrench to tight the spark plugs?Most likely the head of your engine is aluminum. Aluminum is a %26quot;soft%26quot; metal and the threads strip very easily. A torque wrench is always recommended for tightening spark plugs and is an absolute must for an aluminum head. Overtighten and you could damage the plug as well as the threads in the engine head. Too loose and the engine won't run properly. The best torque wrench to get is the kind with the %26quot;twist%26quot; adjustment because you can't overtighten with these.
You will also need a spark plug socket, 12in extension (I'll explain later), and recommend some anti seize.
The anti-seize goes ONLY on the threaded portion of the plug. Keep in mind a little goes a loooooong way. The amount you use should be about the size of 1/3 of an eraser of a wood pencil.
When installing spark plugs it is always best to start running them in by hand so you don't %26quot;cross thread%26quot; them. You can use the spark plug socket and extension to do this if you can't reach. You don't have screw them in all the way by hand, just the first 4 or 5 threads (turns). Then you can finish up with the torque wrench.Do we need to use the torque wrench to tight the spark plugs?no. Just get them tight without stripping the threads. They'll be fine.Do we need to use the torque wrench to tight the spark plugs?No, just a simple wrench will doDo we need to use the torque wrench to tight the spark plugs?No torque wrench. Hand tight with rachet only. Take care.Do we need to use the torque wrench to tight the spark plugs?No, you do not need a torque.wrench. If you use a ratchet, just tighten until snug. I have been doing it this way for years and never had a problem.Do we need to use the torque wrench to tight the spark plugs?No it is not necessary, but is a good idea especially considering all the new cars have aluminum heads and you do not want to over tighten or have them too loose. If you can estimate about 20 lb of torque then go for it. I would however strongly recommend applying a SMALL amount of anti-seize to the male threads prior to installation. this will make them easier to remove next time and prevent any problems. be sure to start by hand, or you may cross thread which is a major problemDo we need to use the torque wrench to tight the spark plugs?Well, you can just use an ordinary socket wrench to tightne the spark plugs, but you run the risk of damaging the threads by over tightening the plug.. That can be a lot more expensive than buying a torque wrench. I wouldn't chance it. Plus, you'll have a torque wrench forever!Do we need to use the torque wrench to tight the spark plugs?No, torque is not necessary, just tighten them as you would any thing else but don't strip it. I also recommend buying all platinum spark plugs in stead of just one and the rest regular. It is better for the vehicle and thay will all last longer. They should cost no more that $7.00 to $10.00 a piece depending on the brand name.Do we need to use the torque wrench to tight the spark plugs?hands onlyDo we need to use the torque wrench to tight the spark plugs?I always use a torque wrench so there is absolutly no question the plug is not in too tight or too loose. Also be sure to use anti-seize lubricant on the new plug threads so you can remove them the next time you go to change them.
its regarding my 01 max and i have never changed the spark plugs on my car by myself, but i did changed the coils so i know how to get to the plugs etc, my question is..do i need to buy a torque wrench to tight the plugs or i can just use the rachet and hand tight them? please help me cuz i am on the way of getting this done today.Do we need to use the torque wrench to tight the spark plugs?Most likely the head of your engine is aluminum. Aluminum is a %26quot;soft%26quot; metal and the threads strip very easily. A torque wrench is always recommended for tightening spark plugs and is an absolute must for an aluminum head. Overtighten and you could damage the plug as well as the threads in the engine head. Too loose and the engine won't run properly. The best torque wrench to get is the kind with the %26quot;twist%26quot; adjustment because you can't overtighten with these.
You will also need a spark plug socket, 12in extension (I'll explain later), and recommend some anti seize.
The anti-seize goes ONLY on the threaded portion of the plug. Keep in mind a little goes a loooooong way. The amount you use should be about the size of 1/3 of an eraser of a wood pencil.
When installing spark plugs it is always best to start running them in by hand so you don't %26quot;cross thread%26quot; them. You can use the spark plug socket and extension to do this if you can't reach. You don't have screw them in all the way by hand, just the first 4 or 5 threads (turns). Then you can finish up with the torque wrench.Do we need to use the torque wrench to tight the spark plugs?no. Just get them tight without stripping the threads. They'll be fine.Do we need to use the torque wrench to tight the spark plugs?No, just a simple wrench will doDo we need to use the torque wrench to tight the spark plugs?No torque wrench. Hand tight with rachet only. Take care.Do we need to use the torque wrench to tight the spark plugs?No, you do not need a torque.wrench. If you use a ratchet, just tighten until snug. I have been doing it this way for years and never had a problem.Do we need to use the torque wrench to tight the spark plugs?No it is not necessary, but is a good idea especially considering all the new cars have aluminum heads and you do not want to over tighten or have them too loose. If you can estimate about 20 lb of torque then go for it. I would however strongly recommend applying a SMALL amount of anti-seize to the male threads prior to installation. this will make them easier to remove next time and prevent any problems. be sure to start by hand, or you may cross thread which is a major problemDo we need to use the torque wrench to tight the spark plugs?Well, you can just use an ordinary socket wrench to tightne the spark plugs, but you run the risk of damaging the threads by over tightening the plug.. That can be a lot more expensive than buying a torque wrench. I wouldn't chance it. Plus, you'll have a torque wrench forever!Do we need to use the torque wrench to tight the spark plugs?No, torque is not necessary, just tighten them as you would any thing else but don't strip it. I also recommend buying all platinum spark plugs in stead of just one and the rest regular. It is better for the vehicle and thay will all last longer. They should cost no more that $7.00 to $10.00 a piece depending on the brand name.Do we need to use the torque wrench to tight the spark plugs?hands onlyDo we need to use the torque wrench to tight the spark plugs?I always use a torque wrench so there is absolutly no question the plug is not in too tight or too loose. Also be sure to use anti-seize lubricant on the new plug threads so you can remove them the next time you go to change them.
Where can I recycle spark plugs?
As a materials engineer I know how toxic Yttrium and Platinum can be if disposed of improperly. I just wanted to know if there is somewhere I can safely recycle my old spark plugs. If it helps, I live in Pittsburgh, PA.Where can I recycle spark plugs?You might want to check the EPA website for drop-off locations. Most communities have a annualy hazardous waste drop-off day where people can bring old paint, oil, etc. for recycling or proper disposal.
How to change the spark plugs in a 1986 nissan 300sx?
Im having trouble figuring out how to chane the spark plugs do i have to pull the intake manifold ?How to change the spark plugs in a 1986 nissan 300sx?i have the exact same car. the chilton book i have says to just remove the wire and you should be able to twist the plug out.hair bands How often do you wash your bed sheets
How to replace spark plugs on2004 Amanti Kia?
I have a 2004 Amanti,Kia that I would like to replace the spark plugs. Is their any step by step process to do this. Is there any website, that would give me detailed information on how to do this? Outside of purchasing the spark plugs are there any gaskets that would need to be replaced etc.?How to replace spark plugs on2004 Amanti Kia?If you plan on DIY pick up a haynes repair manual and it will help you in all aspects of the tune up and any other things you would like to tackle in the future. It should take you a couple of hrs so take your time .
How to change spark plugs and wires?
I have a 2002 Chrysler town %26amp; country Limited with 105K miles on it. Due to very low mileage (12 mpg), I need to change the spark plugs (and possibly wires). I will appreciate if anybody could provide me instructions (Do's and Dont's) so that I can do it on my own. ThanksHow to change spark plugs and wires?Make sure you mark the position of each wire. Make sure you have the proper spark plug socket (with a rubber insert in it to protect the plug) Don't over tighten the new plug when installing them. There is not much more.How to change spark plugs and wires?I just changed the plugs on our 2002 town and country. All the sites I saw said that you had to remove a bunch of stuff to get at the rear plugs. I was able to reach back there and get at them. I had to use extensions of various lengths with my sockets, but I was able to get at them. Took 1 hour.
one end will be where you place plugs into the engine the other end will be your distributor cap - as you take out plugs from your dist cap make sure you number them with tape ( masking tape ) this is your fireing order and you do not want to mess this up -
buy the pregapped plugs if your not familiar with changing them this way you dont have to worry about the gaping tool - i cant stand them personally -
and basically all you have to do is unplugg from each end replace your plug and wires -
since you arent getting good milage consider replaceing your air filter also -How to change spark plugs and wires?View the Advance Auto online %26quot;todays tuneups%26quot; video for the basic spark plug and wire installation
http://www.advanceautoparts.com/english/How to change spark plugs and wires?go to the parts store, pick up a haynes maintenance manual, how many cylinders does your engine have, pick up that many spark plugs, and wires, rent or buy a torque wrench, a distributer cap and rotor and an airfilter. mark everything where you find it. if you want to save a bit of money, skip the manual (they are handy to have for other maintenance stuff, though) and get everything else. You can get the torque values from the internet and the firing order should be stamped on the engine block, also the cylinder numbers should also be stamped on the block. Before you remove the wires, mark them the same as the cylinder numbers from which you removed them. leave them attatched to the distributer cap!!!! But make sure you mark them to match the cylinder mark on the block!! Then remove and replace the plugs, use the torque values. . . check each plug as they come out. there should be a nice uniform greyish white burnt look to them. note where the ones that look different came from and use the internet to find out what could have caused any irregular deposits on them. Then one by one replace the wires, making sure that you plug them all up to the same reciever on the distributer cap from which you removed them ONE AT A TIME!!! , them, remove the distributer cap, and line it up with the old one and trade the wires over to the new one, one by one, making sure that they are all in the SAME place they were on the old one, set aside, replace the rotor, you just pull it out and put the new one in, in the same position you found the old one in. then you reattatch the distributer cap and you should be on your way with MUCH better gas mileage!! Oh!! also replace your airfilter. . . umm you might also replace your fuel filter as well, sometimes it gets clogged up and messes with you mileage. . .? Good luck and I hope I helped some!! ^_^
Report Abuse
How to change spark plugs and wires?well you should easily be able to locate your spark plug wires and that would be the easiest thing -one end will be where you place plugs into the engine the other end will be your distributor cap - as you take out plugs from your dist cap make sure you number them with tape ( masking tape ) this is your fireing order and you do not want to mess this up -
buy the pregapped plugs if your not familiar with changing them this way you dont have to worry about the gaping tool - i cant stand them personally -
and basically all you have to do is unplugg from each end replace your plug and wires -
since you arent getting good milage consider replaceing your air filter also -How to change spark plugs and wires?View the Advance Auto online %26quot;todays tuneups%26quot; video for the basic spark plug and wire installation
http://www.advanceautoparts.com/english/How to change spark plugs and wires?go to the parts store, pick up a haynes maintenance manual, how many cylinders does your engine have, pick up that many spark plugs, and wires, rent or buy a torque wrench, a distributer cap and rotor and an airfilter. mark everything where you find it. if you want to save a bit of money, skip the manual (they are handy to have for other maintenance stuff, though) and get everything else. You can get the torque values from the internet and the firing order should be stamped on the engine block, also the cylinder numbers should also be stamped on the block. Before you remove the wires, mark them the same as the cylinder numbers from which you removed them. leave them attatched to the distributer cap!!!! But make sure you mark them to match the cylinder mark on the block!! Then remove and replace the plugs, use the torque values. . . check each plug as they come out. there should be a nice uniform greyish white burnt look to them. note where the ones that look different came from and use the internet to find out what could have caused any irregular deposits on them. Then one by one replace the wires, making sure that you plug them all up to the same reciever on the distributer cap from which you removed them ONE AT A TIME!!! , them, remove the distributer cap, and line it up with the old one and trade the wires over to the new one, one by one, making sure that they are all in the SAME place they were on the old one, set aside, replace the rotor, you just pull it out and put the new one in, in the same position you found the old one in. then you reattatch the distributer cap and you should be on your way with MUCH better gas mileage!! Oh!! also replace your airfilter. . . umm you might also replace your fuel filter as well, sometimes it gets clogged up and messes with you mileage. . .? Good luck and I hope I helped some!! ^_^
How hard is it to change spark plugs on a 2001 ford lightning?
I'm doing it for the first time but I want to see if I can do it by myself, and what kind of spark plugs I should use?How hard is it to change spark plugs on a 2001 ford lightning?i don't know may a branded one should do
HELP PLSValve cover seal that has leaked oil into spark plugs? How do I remove oil and effectively change seal?
I have a 92 Accord that has a lot of oil leaked into the spark plugs and has lost power. It is only 3 of the plugs and they are soaked in oil. What are some specifics I need to know about changing out the seal and removing any oil that is around the spark plugs or anywhere else that may mess up the engine?
How much silicon do i need and where does it go?HELP PLSValve cover seal that has leaked oil into spark plugs? How do I remove oil and effectively change seal?You will need to replace the spark plug seals and the valve cover gasket. It all comes in a set. You won't need too many tools. You will need to remove the plugs and clean them off and clean the spark plug boots. You can get the oil out with paper towels. You will not get all of it out. Some will go into the cylinder when you remove the plug, but that won't hurt anything. It might smoke a little when you first start it up after fixing this, but it should go away within 10 or 20 seconds.
I just did this on the same kind of car about 6 months ago. I usually put a rag over the hole and blow air down in there, it will blow out all the oil and dirt. If you are still nervous about doing this yourself, go get the Chilton's or Haynes manual for it. They are only about $20. It will save you lots of headaches later, trust me.HELP PLSValve cover seal that has leaked oil into spark plugs? How do I remove oil and effectively change seal?New cars use a seal that doesn't need silicon to seal. Get the gasket, or new cover, and clean the oil out with a rag. Unplug the coil wire and turn the car over so the oil in the hole will blow out. Clean area well reinstall new gasket and then the cover. Tighten to specs, install plugs and wires, Ready to go for a 100,000 miles, give or take.HELP PLSValve cover seal that has leaked oil into spark plugs? How do I remove oil and effectively change seal?Check the gasket box before using silicone . Most good brands do not need any sealant , but if it does , use Permatex Non-hardening gasket sealer - not silicone . As far as plugs , a spray cleaner such as Berryman B-12 will do them . Only problem may be the plug wires . If they are very soaked , you will be better off just replacing them .HELP PLSValve cover seal that has leaked oil into spark plugs? How do I remove oil and effectively change seal?92 Accord, mean you don't want to spend unless you have to!
So a combination of some of the previous answer is the way to go!
Permatex is good only when you got good surfaces to seal, but when you got a warped valve cover you better of with the silicone sealant, it will seal quite big gaps! Let it set before you start the engine! and clean the surface to be sealed with petrol (gasoline). You should be able to pick up a tube silicon sealant from most car accessory shops. I assume you don't have access to compressed air!?
Otherwise you could get a can of cheap degreaser spray, spray around the oil leak and wash it of with the garden hose. But than you need to blow the water of from it until it is perfectly dry!
So here is Rich C, right with the get the plugs out, clean most of the oil off with a cloth, Crank the engine so it blows out the extra oil. keep cleaning it with the cloth, until it is clean. When it lost power than you possible should invest into some new plugs. And check the oil level if you still got enough oil in the sump! Good luck!
How much silicon do i need and where does it go?HELP PLSValve cover seal that has leaked oil into spark plugs? How do I remove oil and effectively change seal?You will need to replace the spark plug seals and the valve cover gasket. It all comes in a set. You won't need too many tools. You will need to remove the plugs and clean them off and clean the spark plug boots. You can get the oil out with paper towels. You will not get all of it out. Some will go into the cylinder when you remove the plug, but that won't hurt anything. It might smoke a little when you first start it up after fixing this, but it should go away within 10 or 20 seconds.
I just did this on the same kind of car about 6 months ago. I usually put a rag over the hole and blow air down in there, it will blow out all the oil and dirt. If you are still nervous about doing this yourself, go get the Chilton's or Haynes manual for it. They are only about $20. It will save you lots of headaches later, trust me.HELP PLSValve cover seal that has leaked oil into spark plugs? How do I remove oil and effectively change seal?New cars use a seal that doesn't need silicon to seal. Get the gasket, or new cover, and clean the oil out with a rag. Unplug the coil wire and turn the car over so the oil in the hole will blow out. Clean area well reinstall new gasket and then the cover. Tighten to specs, install plugs and wires, Ready to go for a 100,000 miles, give or take.HELP PLSValve cover seal that has leaked oil into spark plugs? How do I remove oil and effectively change seal?Check the gasket box before using silicone . Most good brands do not need any sealant , but if it does , use Permatex Non-hardening gasket sealer - not silicone . As far as plugs , a spray cleaner such as Berryman B-12 will do them . Only problem may be the plug wires . If they are very soaked , you will be better off just replacing them .HELP PLSValve cover seal that has leaked oil into spark plugs? How do I remove oil and effectively change seal?92 Accord, mean you don't want to spend unless you have to!
So a combination of some of the previous answer is the way to go!
Permatex is good only when you got good surfaces to seal, but when you got a warped valve cover you better of with the silicone sealant, it will seal quite big gaps! Let it set before you start the engine! and clean the surface to be sealed with petrol (gasoline). You should be able to pick up a tube silicon sealant from most car accessory shops. I assume you don't have access to compressed air!?
Otherwise you could get a can of cheap degreaser spray, spray around the oil leak and wash it of with the garden hose. But than you need to blow the water of from it until it is perfectly dry!
So here is Rich C, right with the get the plugs out, clean most of the oil off with a cloth, Crank the engine so it blows out the extra oil. keep cleaning it with the cloth, until it is clean. When it lost power than you possible should invest into some new plugs. And check the oil level if you still got enough oil in the sump! Good luck!
How do you replace spark plugs in a 2001 grand caravan?
i heard its really hard to replace the spark plugs at the back of the engine...how do i do it?How do you replace spark plugs in a 2001 grand caravan?sometimes those are easier to get to from the bottom if you can get it up on a lift,it makes the job a lot easier to do,good luck.How do you replace spark plugs in a 2001 grand caravan?we own a 98 i feel your pain. If you have a hydrualic jack. jack it up and work from there thats what we didHow do you replace spark plugs in a 2001 grand caravan?1 5/8 socket 1 3/8 ratchet 1 swivel peice 1 8'' ext and 1 heat sleeve and maybe a spark plug puller tool and maybe a flat head screw drivercreate seamless digital textures potato bacon soup
How to change the spark plugs on a VW Polo 2004?
I've had the engine cover/air filter off but cannot see where the spark plugs would go can anyone help me please?How to change the spark plugs on a VW Polo 2004?Follow the black ignition leads to the plug caps and they will be under there. Spark plugs are always screwed into the top of the cylinder headHow to change the spark plugs on a VW Polo 2004?Think you have coil packs on that. There might be 4 coil packs on top of the cylinder head (look like black little boxes bout 2%26quot; square) with electrical connection plugs clipped to them. If so there will be 4 screws in each corner of the 4 packs (small might even be torque screws?)
Ignition off, remove electrical connectors, Unscrew the 4 screws and pull off the pack which will have black rubber tube like thing which is popped on to the spark plugs. Your plugs will be down 'da ole'! Remember you must gap the new plugs to the manufactures specs with a feeler gauge. Give the threads some copper slip grease to stop them ceasing in the head.
Failing that, if you still can't find them then your probably driving a diesel.
Ignition off, remove electrical connectors, Unscrew the 4 screws and pull off the pack which will have black rubber tube like thing which is popped on to the spark plugs. Your plugs will be down 'da ole'! Remember you must gap the new plugs to the manufactures specs with a feeler gauge. Give the threads some copper slip grease to stop them ceasing in the head.
Failing that, if you still can't find them then your probably driving a diesel.
What is the standard period to keep spark plugs in the warehouse?
HOW LONG PERIOD OF KEEPING SPARK PLUGS IN WARHOUSE?What is the standard period to keep spark plugs in the warehouse?There isn't an expiration date on spark plugs.......What is the standard period to keep spark plugs in the warehouse?As long as you keep paying the rent on the warehouse.
Where are the spark plugs located on a 2000 Ford Expedition XLT 8 cyclinder?
I've been trying to change the spark plugs on my 00 Expedition for a couple of weeks but I can't find them. I asked at the Ford Dealership but they won't tell me because they want me to pay for a tune up instead. If anyone can tell me the location and how to get to them I would appreciate it greatly!Where are the spark plugs located on a 2000 Ford Expedition XLT 8 cyclinder?There is an individual coil for each cylinder and the spark plugs are located about 5 inches down inside the cylinder heads under each coil. And let's not forget that you need a 7mm 1/4%26quot; drive universal socket that costs 50 bucks to get to the 7 and 8 coils, and triple jointed fingers. It is not an easy job to change plugs on these engines, we usually charge 3 hours labor to change them, it is not a job that the usual vehicle owner can do. I would also suggest you let the dealer change them, they have done many and will save you a lot of pain and time. I always end up bleeding from somewhere after changing plugs on this engine.Where are the spark plugs located on a 2000 Ford Expedition XLT 8 cyclinder?First of all your vehicle doesn't have a distributor nor spark plugs wires. So if you are looking for that you won't find them. Each spark plug has it own individual coil. they are located on top of the engine on the intake manifold right beside each fuel injector. a ratchet with an extension, a swivel and appropriate spark plug socket should do the trick. My suggestion would be to purchase a manual for you vehicle to assist in your maintenence.Where are the spark plugs located on a 2000 Ford Expedition XLT 8 cyclinder?just fallow the wires from the bistributor cap if you dont know what that is dont change em
--------------------
Stick to what you know, kid. Whatever that may be, because cars ain't it and no Ford SUV has had a distributor since about 1996..
Anyway, odds are you need a tune up. Those 8 ignition coils Fail a lot.
You can buy them online at Global for $10 a piece. They can be tough to get to, though.Where are the spark plugs located on a 2000 Ford Expedition XLT 8 cyclinder?I have to agree with bdfy6969 i have about 100 dollars worth of tools i bought just to do the spark plugs in f-series and exped, nav. every time i do one i get scraped up from wrist to elbow inner for arm if you need to ask pay someone to do it for youWhere are the spark plugs located on a 2000 Ford Expedition XLT 8 cyclinder?go to a mechanic...sorry but if you cant even find them your not gona be able to change them when [if] you do...if you must go get a shop manual...15 dollars any auto parts store.Where are the spark plugs located on a 2000 Ford Expedition XLT 8 cyclinder?just fallow the wires from the bistributor cap if you dont know what that is dont change em
--------------------
Stick to what you know, kid. Whatever that may be, because cars ain't it and no Ford SUV has had a distributor since about 1996..
Anyway, odds are you need a tune up. Those 8 ignition coils Fail a lot.
You can buy them online at Global for $10 a piece. They can be tough to get to, though.Where are the spark plugs located on a 2000 Ford Expedition XLT 8 cyclinder?I have to agree with bdfy6969 i have about 100 dollars worth of tools i bought just to do the spark plugs in f-series and exped, nav. every time i do one i get scraped up from wrist to elbow inner for arm if you need to ask pay someone to do it for youWhere are the spark plugs located on a 2000 Ford Expedition XLT 8 cyclinder?go to a mechanic...sorry but if you cant even find them your not gona be able to change them when [if] you do...if you must go get a shop manual...15 dollars any auto parts store.Where are the spark plugs located on a 2000 Ford Expedition XLT 8 cyclinder?just fallow the wires from the bistributor cap if you dont know what that is dont change em
How to replace spark plugs in a 1991 Sentra?
... spark plugs are 19mm. 19mm socket DOES NOT fit down the shaft. How to install if this is the case?How to replace spark plugs in a 1991 Sentra?19mm spark plug socket are available.
They are deeper.
They are deeper.
How to change spark plugs inside cars?
Hello again =]
I had an Xterra 01 and I'm sure i have to change spark plugs. But since i never done it and I don't want to ruin or break them inside I wonder if some1 can tell me exactly and what tools to use to change them?
It's all the same for every cars?.. Same tools same methods?How to change spark plugs inside cars?It's the same for every car.
1) Remove the cover, if there is one (usually says DOHC or some nonsense like that).
2) Remove the wires, making note of their order (crucial). If you have a four cylinder, there will be four.
3) Using a spark plug socket that fits your car (this differs car-to-car), unscrew the spark plugs
4) Gap the new spark plugs, if needed
5) Gently install the new spark plugs by finger tightening, then using your ratchet to just snug it in place - do not overtighten!
6) Replace wires and cover, making sure the wires go back on in the correct order
Just be gentle, don't force anything, and you'll be fine. It might be the easiest thing to do next to replacing the air filter.How to change spark plugs inside cars?It's pretty straight forward. Find spark plugs, remove spark plug wires, unscrew/remove spark plugs, screw/install new plugs, replace wires.
Here is a simple guide with pictures:
http://autorepair.about.com/od/regularma
It becomes difficult if the plugs are in a tight spot with little clearance, I'm not sure how it is on your car.
To be sure to get the right spark plug socket, buy the plugs from an auto parts store, then remove one from the box and find the socket that fits it.
Tip: Either label the spark plug wires, or do one at a time. You don't want to mix up which wires go on which plugs.advise for investment banking nappy hair
I had an Xterra 01 and I'm sure i have to change spark plugs. But since i never done it and I don't want to ruin or break them inside I wonder if some1 can tell me exactly and what tools to use to change them?
It's all the same for every cars?.. Same tools same methods?How to change spark plugs inside cars?It's the same for every car.
1) Remove the cover, if there is one (usually says DOHC or some nonsense like that).
2) Remove the wires, making note of their order (crucial). If you have a four cylinder, there will be four.
3) Using a spark plug socket that fits your car (this differs car-to-car), unscrew the spark plugs
4) Gap the new spark plugs, if needed
5) Gently install the new spark plugs by finger tightening, then using your ratchet to just snug it in place - do not overtighten!
6) Replace wires and cover, making sure the wires go back on in the correct order
Just be gentle, don't force anything, and you'll be fine. It might be the easiest thing to do next to replacing the air filter.How to change spark plugs inside cars?It's pretty straight forward. Find spark plugs, remove spark plug wires, unscrew/remove spark plugs, screw/install new plugs, replace wires.
Here is a simple guide with pictures:
http://autorepair.about.com/od/regularma
It becomes difficult if the plugs are in a tight spot with little clearance, I'm not sure how it is on your car.
To be sure to get the right spark plug socket, buy the plugs from an auto parts store, then remove one from the box and find the socket that fits it.
Tip: Either label the spark plug wires, or do one at a time. You don't want to mix up which wires go on which plugs.
Do more expensive spark plugs make a difference?
Do more expensive spark plugs give you better results than ordinary cheap spark plug. How do I know which ones to buy so I get the best performance. Which ones do you recommend?Do more expensive spark plugs make a difference?i own a repair shop,and yes if your talking about the difference in a plug like a Bosch,,or ngk,,yes they do as compared to a champion plug,,actually Bosch platinum plugs are the best you can buy for the money,and they will out last all the others also,,i use them in the shop,,because i don't want my customers to have problems out on the road,,and i have always had them give good service in my vehicles also,,but there is a difference in good and bad,,or cheap,,either way you look at it,,these days,you get what you pay for,,good luck,i hope this help,s.Do more expensive spark plugs make a difference?they will amplify any other mods u do only really effective if your after another tenth of a second in a lap time normal life not worth feck all. and it would want to be the batman superman love child of a spark plug on l.s.d t get u an extra tenthDo more expensive spark plugs make a difference?Yes it does make a difference, just like everything else the better quality the better you pay, Me I like the splitfires better, but thats just a personal opinion.Do more expensive spark plugs make a difference?As a general rule of them, we replace plugs on Customers car's with OEM spec plugs. If they request different plugs, that is not an issue. Bosch Platinum plugs are very good plugs as well, but I am a bit skeptical about the %26quot;100,000 mile tuneup.%26quot; A super expensive Iridium plug wont give you any performance gains in a regular car, but a cheap off brand plug could cost you some.
On another note, for performance engines, I find autolite's to be very good plugs. Denso has a HUGE selection of heat ranges, which is really nice in find tuning a modded engine. One thing I do not like about Denso plugs, however, is that the tips of the spark plugs screw on, so they can vibrate loose and create a miss. I have seen it happen and the first time I saw it it was difficult to find, because it is the last thing you would expect.
JimDo more expensive spark plugs make a difference?Yes thats why they cost more. depends on what kind of car you have. I have had good luck with Autolite platnium ,denso irridium plugs also with Bosch ust depends on vehicle mfg,Do more expensive spark plugs make a difference?Better results.... they last longer, as in Platinums, but they wont give you like 50 horsepower and drop you from 16 to 12 secs in the quarter mile. The only advantage is that you wont have to change them as often..... In my experience of 25 years working on cars Champion is the best IMO..... NGK is the worst...alot of rim firing. But everyone has their own preference.
On another note, for performance engines, I find autolite's to be very good plugs. Denso has a HUGE selection of heat ranges, which is really nice in find tuning a modded engine. One thing I do not like about Denso plugs, however, is that the tips of the spark plugs screw on, so they can vibrate loose and create a miss. I have seen it happen and the first time I saw it it was difficult to find, because it is the last thing you would expect.
JimDo more expensive spark plugs make a difference?Yes thats why they cost more. depends on what kind of car you have. I have had good luck with Autolite platnium ,denso irridium plugs also with Bosch ust depends on vehicle mfg,Do more expensive spark plugs make a difference?Better results.... they last longer, as in Platinums, but they wont give you like 50 horsepower and drop you from 16 to 12 secs in the quarter mile. The only advantage is that you wont have to change them as often..... In my experience of 25 years working on cars Champion is the best IMO..... NGK is the worst...alot of rim firing. But everyone has their own preference.
Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?
Hi, I have found a motorcycle engine, its a 250cc and its air colled. is there any way i can start it with the kickstar alone, without power to the spark plugs?, or how can i get it going to see if it works?. i dont have any of the bike parts, i just have the engine.
Thanks.Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?If it runs on points and not electronic ignition yes, it will start if the motor is in running condition...gas, carb, magneto etc...Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?If you want to get the engine running you need:
carburettors+ fuel
sparkplugs+coil(s)+points n condensor or CDI unit and a battery 6/12volts depending on igntion systems requirements
Another way to know if its a good engine is to do a compression check. remove the spark plug, screw in a motorcycle compression tester, hold the carbs open( if theyre on the engine) and kick it over to build up the pressure on the gauge.
crap is about 70psi and below.
Ok is about 90
good is about 120psi+
If its a multicylinder then the psi reading must be pretty even across the cylinders if one or more is very low, you need to find out why. i.e 90,125,125,126Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?You don't need any spark plugs. If conditions are right, the engine will start with just a kick like all diesels do.Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?Usually the kick-start turned over a gadget called the Magneto which then produced a spark at the sparkplug, this is more often superseded by a battery and starter motor on modern machines , the battery turning over a starter motor and a generator /alternator producing the spark at the plug.Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?If that doesn't work. Push it down a hill and get to about 5-10mph and drop in 1st gear. Depending on how long the bike has been sitting this may take a few tries.Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?sorry james but it seems you know little about engines ...you will need a spark plug ...allso a battery ..an exhaust system and a fuel tank ...if its a 4 stroke you will need an oil tank ..leave it where you found it ..Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?Funny how everyone seems to have read the question differently to me.
When you kick the engine over, it will generate power to the plug, unless:
1. it's the kind of engine that needs a battery as part of the ignition system;
2. there's something wrong with the generator/magneto/dynamo;
3. ditto plug lead(s);
4. ditto spark plug(s);
5. ditto contact breaker points or CDI unit.
6. any combination of the above.
So technically, the answer to your question is, no, you can't start it without power to the spark plugs.
To get it going, as well as having the above in working order, you'll need a fuel supply. In your case, with just an engine and no cycle parts, that can be rigged up by some kind of tank with a tap in it mounted above the motor (e.g. motor on floor, tank on bench or table) with the fuel line running to the carburettor(s). (Presumably your motor has the carburettors attached?!!)
Have a good look around the site below. Happy tinkering!Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?You'll need a battery and all necessary ignition components, ignore anyone who says you won't.Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?you definitely need spark plugs. The kickstart should turn the engine over and provide a little power to the sparkplug and fire it up. If it is a single cylinder it may not need a battery (Vespas don't have one). If you have sufficient mechanical knowledge you should be able to get it running. If you don't, you won't get it running
Thanks.Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?If it runs on points and not electronic ignition yes, it will start if the motor is in running condition...gas, carb, magneto etc...Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?If you want to get the engine running you need:
carburettors+ fuel
sparkplugs+coil(s)+points n condensor or CDI unit and a battery 6/12volts depending on igntion systems requirements
Another way to know if its a good engine is to do a compression check. remove the spark plug, screw in a motorcycle compression tester, hold the carbs open( if theyre on the engine) and kick it over to build up the pressure on the gauge.
crap is about 70psi and below.
Ok is about 90
good is about 120psi+
If its a multicylinder then the psi reading must be pretty even across the cylinders if one or more is very low, you need to find out why. i.e 90,125,125,126Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?You don't need any spark plugs. If conditions are right, the engine will start with just a kick like all diesels do.Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?Usually the kick-start turned over a gadget called the Magneto which then produced a spark at the sparkplug, this is more often superseded by a battery and starter motor on modern machines , the battery turning over a starter motor and a generator /alternator producing the spark at the plug.Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?If that doesn't work. Push it down a hill and get to about 5-10mph and drop in 1st gear. Depending on how long the bike has been sitting this may take a few tries.Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?sorry james but it seems you know little about engines ...you will need a spark plug ...allso a battery ..an exhaust system and a fuel tank ...if its a 4 stroke you will need an oil tank ..leave it where you found it ..Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?Funny how everyone seems to have read the question differently to me.
When you kick the engine over, it will generate power to the plug, unless:
1. it's the kind of engine that needs a battery as part of the ignition system;
2. there's something wrong with the generator/magneto/dynamo;
3. ditto plug lead(s);
4. ditto spark plug(s);
5. ditto contact breaker points or CDI unit.
6. any combination of the above.
So technically, the answer to your question is, no, you can't start it without power to the spark plugs.
To get it going, as well as having the above in working order, you'll need a fuel supply. In your case, with just an engine and no cycle parts, that can be rigged up by some kind of tank with a tap in it mounted above the motor (e.g. motor on floor, tank on bench or table) with the fuel line running to the carburettor(s). (Presumably your motor has the carburettors attached?!!)
Have a good look around the site below. Happy tinkering!Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?You'll need a battery and all necessary ignition components, ignore anyone who says you won't.Can a motorcycle engine start with the kick start alone or do you need power to the spark plugs?you definitely need spark plugs. The kickstart should turn the engine over and provide a little power to the sparkplug and fire it up. If it is a single cylinder it may not need a battery (Vespas don't have one). If you have sufficient mechanical knowledge you should be able to get it running. If you don't, you won't get it running
How to change the spark plugs on a 2001 Kia Rio?
What is the best way to change the spark plugs ina 2001 Kia Rio. I know they are tough to get to, but what steps need to be taken to get to the plugs to change them?How to change the spark plugs on a 2001 Kia Rio?You must remove the intake to get to the plugs and replace the gasket on it. It does take a good while to do it from what I have read.
Take a look at http://www.kia-forums.com/kia-sorent...h
Take a look at http://www.kia-forums.com/kia-sorent...h
How do I change the spark plugs on a 1990 300zx NA?
I recently bought spark plugs but I have not been able to even figure out where they are. I do not have an owners manual. I have searched the internet and I can't figure it out. Thanks.How do I change the spark plugs on a 1990 300zx NA?Your 3.0L V6 uses coil over ignition, quite a modern design for 1990.
To replace the plugs, first remove the %26quot;balance tube%26quot; at the top rear of the engine to help gain access to the coils. There is 1 coil per cylinder so simply disconnect the electrical connectors (one at a time) and remover the coil fasteners. Lift the coil up and off the sperk plug. From there it's a straight forward procedure to replace the spark plug.
P.S. Gap spec. is .039%26quot; to .043%26quot;How do I change the spark plugs on a 1990 300zx NA?on gasget headHow do I change the spark plugs on a 1990 300zx NA?is this vehicle model exist?
To replace the plugs, first remove the %26quot;balance tube%26quot; at the top rear of the engine to help gain access to the coils. There is 1 coil per cylinder so simply disconnect the electrical connectors (one at a time) and remover the coil fasteners. Lift the coil up and off the sperk plug. From there it's a straight forward procedure to replace the spark plug.
P.S. Gap spec. is .039%26quot; to .043%26quot;How do I change the spark plugs on a 1990 300zx NA?on gasget headHow do I change the spark plugs on a 1990 300zx NA?is this vehicle model exist?
How do you pull/replace spark plugs in a 2001 Dodge Dakota?
Do you need a special tool to pull the spark plugs out or what? Looks different to me %26amp; I can't get them to come out by twisting or pulling. And yes... I'm a girl.How do you pull/replace spark plugs in a 2001 Dodge Dakota?A sparkplug socket is long and some have a piece of rubber inside to grab it as you pull it out. It is longer to accommodate the longer shape of the spark plug. If you are going to change your own plugs make sure you check the spark plug gaps on the new ones. A Haynes manual would come in very handy. you can pick one up at Advanced Auto parts. The manual is very user friendly and will show the right tools you need for the job.How do you pull/replace spark plugs in a 2001 Dodge Dakota?They unscrew like any other spark plug. You may need a smaller spark plug socket.Queen duvet set on full bed use vigorol relaxer in hair
How do you get to Spark Plugs on a 2002 Jeep Liberty that needs to be replaced?
How do you get ti the spark Plugs on a 2002 Jeep Liberty , 3.7 V6How do you get to Spark Plugs on a 2002 Jeep Liberty that needs to be replaced?pull of the dust covers :)How do you get to Spark Plugs on a 2002 Jeep Liberty that needs to be replaced?To change the plugs on this engine you will need to remove the intake air box and duct. Find the coil packs for each cylinder. Remove the plug and install the new ones. The ignition coils are the black gadgets that have an electrical connector to it and are bolted onto the intake manifold with a small nut. The spark plugs are pretty deep into the engine head. Be careful when threading in the new spark plugs because these engines have aluminum heads with aluminum threads which can be easily damaged if over torqued.
How do I change the spark plugs on my 98 Windstar?
98 Windstar 3.0L V6 (12 valve Vulcan). I need to know how to change the spark plugs. The front 3 are easy to get out but how do I get at the back ones/ Also I'm changing the wires, any help would be great.How do I change the spark plugs on my 98 Windstar?You need to pull the intake cover off, but don't undo the fuel rails. Get all the hoses secured out of the way. You should be able to reach the plugs that way, but you won't be able to see 2 of them. Use a mirror, a good light, and an offset pivoting head ratchet and 16mm deep socket. If there is visible debris around the plugs, blow it off before starting, and give the plugs a good spray of penetrating oil an hour before starting to remove them. Be extremely careful, because in the awkward position you'll be in, it's easy to break an old plug (not a devastating situation, but a pain just the same), or you could cross thread a new plug and strip the threads in the head ( a terribly devastating and expensive situation).How do I change the spark plugs on my 98 Windstar?never worked on a winstar. you might try getting to them from under the car, there's more clearance there sometimes, other than that just squeeze back there and pull them. Definitely change the wires ONE AT A TIME, this way your sure to get them in the right firing order. so change a plug then the wire that goes with it. not all at the same time. good luckHow do I change the spark plugs on my 98 Windstar?i think it would be helpful to take off the intake manifoldHow do I change the spark plugs on my 98 Windstar?Remove the front wheels and go into the fender well. You will need to remove the cover and you can see the spark plugs.
How much should it cost to change the spark plugs and replace the transmission fluid/filter on a Grand Prix?
I have a 2002 Pontiac Grand Prix SE. It has 102,000 miles on it and I'm wondering roughly what it should cost to have the spark plugs replaced and have my transmission fluid and filter changed. I live in LA.
ThanksHow much should it cost to change the spark plugs and replace the transmission fluid/filter on a Grand Prix?Josh didn't mention changing his transmission filter so, add about $20 or so.
Yes, you %26quot;have%26quot; to have the plat. plugs or else your Check Engine light will come on.
The Plat. plugs are also why you got 102k out of your first ones.
Not sure about the LA area but, 6 plugs at about $15 a piece is normal - plus labor if a garage does it.
[Plus beers, if I do it... :) ]
[[Correction, %26quot;plus beers as I watch you do it and I supervise.%26quot;]]
Total should be less than $200 if you do it. $325ish if done at a shop.How much should it cost to change the spark plugs and replace the transmission fluid/filter on a Grand Prix?Considering, it's a 2002 with that many miles i would also have the spark plus wires replaced. Get the platinum spark plugs.
I had my done by the dealer for about 85 dollars.
Also, I changed the fluid myself. The fluid is expensive for this car type. You need type IV.
I used Castrol and it took 4 quarts costing 6 bucks a piece.
So your looking at about 125-150 bucks if you do the tranny fluid yourself.
ThanksHow much should it cost to change the spark plugs and replace the transmission fluid/filter on a Grand Prix?Josh didn't mention changing his transmission filter so, add about $20 or so.
Yes, you %26quot;have%26quot; to have the plat. plugs or else your Check Engine light will come on.
The Plat. plugs are also why you got 102k out of your first ones.
Not sure about the LA area but, 6 plugs at about $15 a piece is normal - plus labor if a garage does it.
[Plus beers, if I do it... :) ]
[[Correction, %26quot;plus beers as I watch you do it and I supervise.%26quot;]]
Total should be less than $200 if you do it. $325ish if done at a shop.How much should it cost to change the spark plugs and replace the transmission fluid/filter on a Grand Prix?Considering, it's a 2002 with that many miles i would also have the spark plus wires replaced. Get the platinum spark plugs.
I had my done by the dealer for about 85 dollars.
Also, I changed the fluid myself. The fluid is expensive for this car type. You need type IV.
I used Castrol and it took 4 quarts costing 6 bucks a piece.
So your looking at about 125-150 bucks if you do the tranny fluid yourself.
I have some oil getting into my spark plugs how much to repiar?
I have a 1996 honda Accord LX, and i have some oil getting into my spark plugs, i believe i need to replace the O rings that stop the oil from getting into the spark plug area. I go to a repair shop that is near my house and is family owned. They gave me an estimate of around $500 to repiar seems kind of high, but they do give a warranty on the service... Not sure if is too much or if i should go elsewhere.I have some oil getting into my spark plugs how much to repiar?Sounds like you dont know what has to be done...thats kinda lowI have some oil getting into my spark plugs how much to repiar?it depends but that seems to be right ..
but its a hell of a lot cheaper if you do it all yourself.
just get the parts at autozone.I have some oil getting into my spark plugs how much to repiar?that does sound about right cuz they could have to tear into the head but there could be some other problems like burnt rings around the piston but i do doubt that unless your getting like a blueish smoke out of you exhaust so i would recommend taking it to the shop
but its a hell of a lot cheaper if you do it all yourself.
just get the parts at autozone.I have some oil getting into my spark plugs how much to repiar?that does sound about right cuz they could have to tear into the head but there could be some other problems like burnt rings around the piston but i do doubt that unless your getting like a blueish smoke out of you exhaust so i would recommend taking it to the shop
How long should it take a Mechanic too change the spark plugs in a 2000 Dodge Grand Caravan w/ 3 Litre V6?
Just want to have a rough idea of how much labour time I can expect for the mechanic too change my spark plugs.How long should it take a Mechanic too change the spark plugs in a 2000 Dodge Grand Caravan w/ 3 Litre V6?usually around an hour ,if nothing goes wrong ,but i have had some of those that would take longer because the plugs are really hard to get out sometimes,and a good mechanic wont try and force them out,he or she, will get them loose then use a penetrating oil to help them come the rest of the way out,it once took me over two hours to get a set out so be prepared just in case,most of the time on a 3.0 they come out fairly easy though,good luck.How long should it take a Mechanic too change the spark plugs in a 2000 Dodge Grand Caravan w/ 3 Litre V6?your welcome.
Hope that helps and best of luck.By the way I'd not want to just do the plugs on that vehicle one thing you could do or have a friend or mechanic do is disconnect the spark-plug wires one by one at the ignition coil , take a wire brush and sandpaper and clean the connectors and be sure to dust off the sand afterwards.You might find by just doing that the engine starts to run better most ppl don't do that at all and have sever bad corroded or rusty connections on their ignition modules.How long should it take a Mechanic too change the spark plugs in a 2000 Dodge Grand Caravan w/ 3 Litre V6?1 hrs more then that the mechanic is stealing your money!How long should it take a Mechanic too change the spark plugs in a 2000 Dodge Grand Caravan w/ 3 Litre V6?actually i have that engine in my car and they should charge u around 5 hours (that's the book time) or less depending on how good the mechanic is because they have to pull off the intake plenum which is where the back three plugs are.emo myspace what love song would you dedicate to
Report Abuse
How long should it take a Mechanic too change the spark plugs in a 2000 Dodge Grand Caravan w/ 3 Litre V6?it takes a bout an hour if he is slow so just u can judge around thatHow long should it take a Mechanic too change the spark plugs in a 2000 Dodge Grand Caravan w/ 3 Litre V6?try it and seeHow long should it take a Mechanic too change the spark plugs in a 2000 Dodge Grand Caravan w/ 3 Litre V6?Just say 5 to 10 or more mins per plug especially if he has all the right tools and knows the engine well.Hope that helps and best of luck.By the way I'd not want to just do the plugs on that vehicle one thing you could do or have a friend or mechanic do is disconnect the spark-plug wires one by one at the ignition coil , take a wire brush and sandpaper and clean the connectors and be sure to dust off the sand afterwards.You might find by just doing that the engine starts to run better most ppl don't do that at all and have sever bad corroded or rusty connections on their ignition modules.How long should it take a Mechanic too change the spark plugs in a 2000 Dodge Grand Caravan w/ 3 Litre V6?1 hrs more then that the mechanic is stealing your money!How long should it take a Mechanic too change the spark plugs in a 2000 Dodge Grand Caravan w/ 3 Litre V6?actually i have that engine in my car and they should charge u around 5 hours (that's the book time) or less depending on how good the mechanic is because they have to pull off the intake plenum which is where the back three plugs are.
What spark plugs and oil filter do I need for a 1996 Corsa?
Is it hard to fit them yourself? Any links to videos to show me how to fit them? What would I have to do to service my own car? Change spark plugs, air filter, oil filter, oil change anything else?What spark plugs and oil filter do I need for a 1996 Corsa?sounds as if you should leave it to the expertsWhat spark plugs and oil filter do I need for a 1996 Corsa?What size engine? is it automatic or standard? turbo charged or not? does it have A/C or not?
These are all required before you can source the correct part for your car. Once you have all this info, call or visit your local auto parts store and they will set you upWhat spark plugs and oil filter do I need for a 1996 Corsa?Pop into Halfords. They have reference sheets that will tell you what bits for what car. I also strongly recommend that you invest in a Haynes Manual (also in Halfords). It's 20 but will save you that many times over. If you can't afford it ask Mum or Dad to get it as a birthday pressie.What spark plugs and oil filter do I need for a 1996 Corsa?******* liverpool fans and their vauxhall corsa's....
These are all required before you can source the correct part for your car. Once you have all this info, call or visit your local auto parts store and they will set you upWhat spark plugs and oil filter do I need for a 1996 Corsa?Pop into Halfords. They have reference sheets that will tell you what bits for what car. I also strongly recommend that you invest in a Haynes Manual (also in Halfords). It's 20 but will save you that many times over. If you can't afford it ask Mum or Dad to get it as a birthday pressie.What spark plugs and oil filter do I need for a 1996 Corsa?******* liverpool fans and their vauxhall corsa's....
How often do spark plugs need to be changed?
On a 2002 Jeep Liberty, 3.7L, 6cylinder, with 59,150 miles. Is there a recommended mileage that the spark plugs should be changed at?How often do spark plugs need to be changed?your owners manual will tell you for sure but most new vehicles are good up to 100,000 miles unless your experiencing hard starts and loss of fuel mileage.How often do spark plugs need to be changed?Plug life depends on the plugs if nothing is amiss in your engine.
Platinum and Iridium plugs can go a long time without needing to be replaced. I usually run plain jane copper plugs and replace every 12,000-15,000 miles based on the amount the gap has changedHow often do spark plugs need to be changed?you can go 90000 unless you have a seal leak and its getting on the plug and causing a misfire but now plugs go forever
Platinum and Iridium plugs can go a long time without needing to be replaced. I usually run plain jane copper plugs and replace every 12,000-15,000 miles based on the amount the gap has changedHow often do spark plugs need to be changed?you can go 90000 unless you have a seal leak and its getting on the plug and causing a misfire but now plugs go forever
How do I change spark plugs in my 1500 Vulcan?
I bot a 1998 1500 Vulcan last week and it seems to be missing some. I want to change the spark plugs but was wondering if there is a trick to it. I dont mean to soung stupid, but I tried pulling on the plug wires and it would not come off.How do I change spark plugs in my 1500 Vulcan?my answer is try to check it out first on auto repair shop..dude
How to get to the Back spark plugs on 2000 chevy Malibu 6 cly?
I can see where the wires go but just sure the best way to get to the back 3 spark plugs.How to get to the Back spark plugs on 2000 chevy Malibu 6 cly?This is REALLY interesting!!! The procedure is this. Dislocate the front motor mounts. Then, using, a strap, rotate the engine towards you until you can gain access. It is really cool to watch done. I hope you have the good sense to be using a higher tech spark plug, like a Bosch Fusion, or Nippondenso Twin Tip plug. These will give better fuel mileage and power than the factory installed plugs. Also, vital sensors will last longer over time. You will save $$$$!!How to get to the Back spark plugs on 2000 chevy Malibu 6 cly?Reach
You can go underneath and reach up.
Use a good ratchet with extensions and swivel. When loose use a hose the size of the plug to take it out the final amount.How to get to the Back spark plugs on 2000 chevy Malibu 6 cly?disconnect your motor mount and pull the engine with a come-along or the special tool designed for it.How to get to the Back spark plugs on 2000 chevy Malibu 6 cly?underneath is good but sometimes the exhaust will be in the way. on the top of the engine there will be a single or couple of engine braces that look like dumbbells. these will be used to tilt the engine forward toward the radiator. you take one or both off the engine roll the engine forward toward the radiator the either chain or refasten the braces. this will give you access to the rear plugsHow to get to the Back spark plugs on 2000 chevy Malibu 6 cly?depending on the particular model, you may find it easier to raise the vehicle up (safety first,chocks, jack stands,level ground) and reach up from below .with a good light you should be able to see the plug wire boots easily between the rear of the engine and the firewall.there are a few GM front drive /transverse V-6 models that have an intake plenum that interferes with spark plug removal on the rear side and the upper intake section needs to be removed...i don't believe that this is the case with the malibu.make sure to use a high quality plug so you don't need to get under there for several more years again.good luck.How to get to the Back spark plugs on 2000 chevy Malibu 6 cly?if you can,t reach them then you might have to get them from under the car.
You can go underneath and reach up.
Use a good ratchet with extensions and swivel. When loose use a hose the size of the plug to take it out the final amount.How to get to the Back spark plugs on 2000 chevy Malibu 6 cly?disconnect your motor mount and pull the engine with a come-along or the special tool designed for it.How to get to the Back spark plugs on 2000 chevy Malibu 6 cly?underneath is good but sometimes the exhaust will be in the way. on the top of the engine there will be a single or couple of engine braces that look like dumbbells. these will be used to tilt the engine forward toward the radiator. you take one or both off the engine roll the engine forward toward the radiator the either chain or refasten the braces. this will give you access to the rear plugsHow to get to the Back spark plugs on 2000 chevy Malibu 6 cly?depending on the particular model, you may find it easier to raise the vehicle up (safety first,chocks, jack stands,level ground) and reach up from below .with a good light you should be able to see the plug wire boots easily between the rear of the engine and the firewall.there are a few GM front drive /transverse V-6 models that have an intake plenum that interferes with spark plug removal on the rear side and the upper intake section needs to be removed...i don't believe that this is the case with the malibu.make sure to use a high quality plug so you don't need to get under there for several more years again.good luck.How to get to the Back spark plugs on 2000 chevy Malibu 6 cly?if you can,t reach them then you might have to get them from under the car.
How many spark plugs does a 1996 vw passat have?
I just got one of those diagnostic reports done at the dealership, since my check engine light went on . They said I need new spark plugs which they want to charge an arm and a leg for, when I can get them for $10 each at the most.How many spark plugs does a 1996 vw passat have?Four or six depending on which engine you have. Unless you have the turbo diesel in which case the answer is none. I would imagine the OE plug to be 10 - 15 dollars each.Labor depends on which engine. Our rate here is 70.00 per hour, so at a minimum you would need 4 plugs at 15.00 and minimum labor of 1 hour, although I would think it is more than 1 hour.
So 4 - 5 hundred dollars for a basic tune up, sounds right in line for a dealership. Perhaps you should consider an independant repair shop.How many spark plugs does a 1996 vw passat have?Depending on the engine it could be as few as 4 or as many as 8, normally passats have a 6cylinder engine which has 6 plugsHow many spark plugs does a 1996 vw passat have?are they charging too much for the plugs or does the quote include installation,you will have either 4 or 6 plugsHow many spark plugs does a 1996 vw passat have?Normally 4 but it depends on the on model, cause you get TDI - which is diesel and use different spark plugs, 1.6/2.0 L which are 4 cylinder cars and uses 4 spark plugs and then you get the V5 which off course has 5 cylinders and therefor uses 5 spark plugs.How many spark plugs does a 1996 vw passat have?In 1996 the passat came with three engines. The
2.0L Inline 4, the 2.8L V 6 and the 1.9L Inline 4.
If you have the 2.0 or 1.9L engine you will need 4 spark plugs. If you have the 2.8L V6 you will require 6.
Sometimes the cost of replacing spark plugs is in the labour involved in changing them. I am not sure about the passat but I do know that some engines have to be lifted in order to change the plugs.How many spark plugs does a 1996 vw passat have?I believe the Passat of this vintage uses regular %26quot;resistor%26quot; spark plugs which can be had anywhere for $2-3.00 each. It's been a while since I've seen a tune up on a VR6 of this age so I don't recall how much fun it is to get at the plugs but V6 labor on a FWD vehicle is usually at least an hour.finction as one pc make acne scars fade
So 4 - 5 hundred dollars for a basic tune up, sounds right in line for a dealership. Perhaps you should consider an independant repair shop.How many spark plugs does a 1996 vw passat have?Depending on the engine it could be as few as 4 or as many as 8, normally passats have a 6cylinder engine which has 6 plugsHow many spark plugs does a 1996 vw passat have?are they charging too much for the plugs or does the quote include installation,you will have either 4 or 6 plugsHow many spark plugs does a 1996 vw passat have?Normally 4 but it depends on the on model, cause you get TDI - which is diesel and use different spark plugs, 1.6/2.0 L which are 4 cylinder cars and uses 4 spark plugs and then you get the V5 which off course has 5 cylinders and therefor uses 5 spark plugs.How many spark plugs does a 1996 vw passat have?In 1996 the passat came with three engines. The
2.0L Inline 4, the 2.8L V 6 and the 1.9L Inline 4.
If you have the 2.0 or 1.9L engine you will need 4 spark plugs. If you have the 2.8L V6 you will require 6.
Sometimes the cost of replacing spark plugs is in the labour involved in changing them. I am not sure about the passat but I do know that some engines have to be lifted in order to change the plugs.How many spark plugs does a 1996 vw passat have?I believe the Passat of this vintage uses regular %26quot;resistor%26quot; spark plugs which can be had anywhere for $2-3.00 each. It's been a while since I've seen a tune up on a VR6 of this age so I don't recall how much fun it is to get at the plugs but V6 labor on a FWD vehicle is usually at least an hour.
Do expensive spark plugs make a difference in engine performance?
i was jsut at autozone and saw these cool looking spark paugs. they were the Bosch plugs with the four iridium and platinum tips or something like that. they were $7.99 each and the box said increase horsepower, so like an idiot i bought them.
i want to know if they are really worth it though. how will they affect engine performance?Do expensive spark plugs make a difference in engine performance?They wont make any significant or noticeable difference over that of what is recommended by the manufacturer.Do expensive spark plugs make a difference in engine performance?Your engine performance will increase, but not enough for you to notice. The benefit with most expensive plugs is that they last longer. But to increase power is a stretch. The term %26quot;specious%26quot; is in order here. It means there is some truth to a statement, but a minor truth of little or no consequence.
You can feel good about your purchase just the same. They could be the last plugs you'll ever need for that car.Do expensive spark plugs make a difference in engine performance?Nope, they don't make any extra power, in fact some will loose power over a std plug.
I have dyno'ed and track tested every spark plug known to man and I can tell you that the only think those fancy plugs do is lighten your wallet.
I have a 500 HP camaro that I drag race in NHRA D.O.T tire class.. Wanna guess what plugs I use?
.
.
.
$1.29 to $1.79 std. AC delco, auto lite or NGK v power plugs
I'm looking for frictions of a horsepower gain and well really if those fancy plugs worked, don't you think I would use them.. Hell with the price if they made more power I would be running them. I have $14K in my car, spend $175 bucks per trip to drag strip just on fuel, $400 set of rear tires that might last 1 year. Whats 64 bucks to gain more power?
They don't work, thats why I don't use them.
I also build race engines. My customers are looking for all the power they can get.. If those fancy plugs made more, I would install them in the engines I build.
Also bosch (reg and plats) are the worst plugs I have ever tried. Fouled out before I made it out of my driveway for a test driveDo expensive spark plugs make a difference in engine performance?they claim that but they can't prove it by me as I have never seen any difference from regular plugs in performance from those special expensive plugs, the only difference I have ever noticed was in regular plugs in my big block chevy where AC plugs is the standard plug and autolite definately makes the car run better than the AC's.Do expensive spark plugs make a difference in engine performance?the only one that will gain with u buying these plugs are bosh,and autozone.....car makers of today spend millions of dollars on research and development,and the spark plugs are tested for performance in the engine that they are in....cars that came with a regular plugs will not benefit from platinum or any other gimmick plug...stick with what your car came with for best performance...take the money u would have wasted on the plugs and put some gas in your car, take a ride and enjoyDo expensive spark plugs make a difference in engine performance?I used to think that way. What I do NOW is change plugs AT LEAST ONCE A YEAR whether I need to or not. I buy the plug that costs $1.79, preferably champion and go for it. I have a fresh plug at least once a year. Car companies are calling for 100000 mile maintenance. Have you ever looked a 100K plug. The whole end is burned off.Do expensive spark plugs make a difference in engine performance?nope
i want to know if they are really worth it though. how will they affect engine performance?Do expensive spark plugs make a difference in engine performance?They wont make any significant or noticeable difference over that of what is recommended by the manufacturer.Do expensive spark plugs make a difference in engine performance?Your engine performance will increase, but not enough for you to notice. The benefit with most expensive plugs is that they last longer. But to increase power is a stretch. The term %26quot;specious%26quot; is in order here. It means there is some truth to a statement, but a minor truth of little or no consequence.
You can feel good about your purchase just the same. They could be the last plugs you'll ever need for that car.Do expensive spark plugs make a difference in engine performance?Nope, they don't make any extra power, in fact some will loose power over a std plug.
I have dyno'ed and track tested every spark plug known to man and I can tell you that the only think those fancy plugs do is lighten your wallet.
I have a 500 HP camaro that I drag race in NHRA D.O.T tire class.. Wanna guess what plugs I use?
.
.
.
$1.29 to $1.79 std. AC delco, auto lite or NGK v power plugs
I'm looking for frictions of a horsepower gain and well really if those fancy plugs worked, don't you think I would use them.. Hell with the price if they made more power I would be running them. I have $14K in my car, spend $175 bucks per trip to drag strip just on fuel, $400 set of rear tires that might last 1 year. Whats 64 bucks to gain more power?
They don't work, thats why I don't use them.
I also build race engines. My customers are looking for all the power they can get.. If those fancy plugs made more, I would install them in the engines I build.
Also bosch (reg and plats) are the worst plugs I have ever tried. Fouled out before I made it out of my driveway for a test driveDo expensive spark plugs make a difference in engine performance?they claim that but they can't prove it by me as I have never seen any difference from regular plugs in performance from those special expensive plugs, the only difference I have ever noticed was in regular plugs in my big block chevy where AC plugs is the standard plug and autolite definately makes the car run better than the AC's.Do expensive spark plugs make a difference in engine performance?the only one that will gain with u buying these plugs are bosh,and autozone.....car makers of today spend millions of dollars on research and development,and the spark plugs are tested for performance in the engine that they are in....cars that came with a regular plugs will not benefit from platinum or any other gimmick plug...stick with what your car came with for best performance...take the money u would have wasted on the plugs and put some gas in your car, take a ride and enjoyDo expensive spark plugs make a difference in engine performance?I used to think that way. What I do NOW is change plugs AT LEAST ONCE A YEAR whether I need to or not. I buy the plug that costs $1.79, preferably champion and go for it. I have a fresh plug at least once a year. Car companies are calling for 100000 mile maintenance. Have you ever looked a 100K plug. The whole end is burned off.Do expensive spark plugs make a difference in engine performance?nope
How can you tell its time to change spark plugs?
I have a 2006 Chevy Impala LTZ 3.9Lt. with 129000 kms. When and how can you tell its time to change the spark plugs. What is the average life of the current spark plugs.How can you tell its time to change spark plugs?During periodic service of 5,000 to 10,000 kms, changing spark plugs are one of the requirements. Failed to change spark plugs can cause, jerking, stalling and hard starting in the morning. Don't wait for the spark plug to malfunctions, i suggest to change it as you service your car. Hope this helps!How can you tell its time to change spark plugs?Most plugs for your year should be change every 100k miles, is car running rough or poor gas mileage.How can you tell its time to change spark plugs?usually about 50k will do it/unleaded gas and allHow can you tell its time to change spark plugs?I'm not any good at converting metric to american, but they're approximately 4 years old now. and are about due. if you notice any misfire on cold starts, especially in wet or damp weather, that is an indication. the bottom line is, for the price of a tune-up, you can more likely add a mile or two per gallon to your fuel average... over a period of time... the tuneup save you money.How can you tell its time to change spark plugs?typically...once every year. if your car has the originals (2006) i believe its safe to say you probably could use a set..How can you tell its time to change spark plugs?When the car doesnt start lol
How often do you change Spark Plugs in your boat?
I have a 2003 Ebbtide Campoine 18.5' Mercruiser 4.3 V6 Alpha one. I just pulled it out of storage started doing the normal routine of cleaning and mechanical upkeep. Gear lube and Oil has been changed before storage (everything up to par) my question is regarding the spark plugs...
When should you change them? Is 3 years too soon? (I'll pull one out tonight and look for corrosion, etc).
Also any other spring time engine recommendations for a 4 year old boat?How often do you change Spark Plugs in your boat?When is the last time you changed your water pump impeller . if you cant remember you maybe due. Real important they get weak with age and take a set when sittng to long and become weak.
If you pull your plugs and the white insulator around the center electrode is light brown they are good . A correct burning plug thats what color it should be Be sure to check all the bellows behind the drives bellhousing and look for drycracking between the webs. if you see any you need it changed.How often do you change Spark Plugs in your boat?As you mentioned, just inspect them. If, the Anode/Electrode not look badly worn they probably OK for another season.
I not have a boat now and am looking, but, the last I had, I kept year round in a slip. Summer it was beached at the camp area and used most everyday. I usually changed plugs in it every summer. It probably got more use than a car.
I tried to find some pictures, many manuals show different plug wear. It a personal preference, but, I do use a little Anti-Seize on my Plugs.How often do you change Spark Plugs in your boat?You fire up on the old spark plugs from the season before, the motor should have been %26quot;fogged%26quot; before it was winterized, burn the old oil out of the motor at start up (IT SMOKES), THEN replace the spark plugs, why foul up %26quot;NEW%26quot; plugs ? they should be changed every spring, changing over to %26quot;NEW%26quot; spark plugs makes a world of difference on an outboard motor, don't forget, it burns %26quot;MIX%26quot;, not straight gasoline like a car (if it's a 2 stroke outboard), so they get dirtier faster than a car's spark plugs.How often do you change Spark Plugs in your boat?I change them at least every 100 hours and clean them at least once a year.How often do you change Spark Plugs in your boat?Just do it every year when it comes out of storage, they are cheap.
When should you change them? Is 3 years too soon? (I'll pull one out tonight and look for corrosion, etc).
Also any other spring time engine recommendations for a 4 year old boat?How often do you change Spark Plugs in your boat?When is the last time you changed your water pump impeller . if you cant remember you maybe due. Real important they get weak with age and take a set when sittng to long and become weak.
If you pull your plugs and the white insulator around the center electrode is light brown they are good . A correct burning plug thats what color it should be Be sure to check all the bellows behind the drives bellhousing and look for drycracking between the webs. if you see any you need it changed.How often do you change Spark Plugs in your boat?As you mentioned, just inspect them. If, the Anode/Electrode not look badly worn they probably OK for another season.
I not have a boat now and am looking, but, the last I had, I kept year round in a slip. Summer it was beached at the camp area and used most everyday. I usually changed plugs in it every summer. It probably got more use than a car.
I tried to find some pictures, many manuals show different plug wear. It a personal preference, but, I do use a little Anti-Seize on my Plugs.How often do you change Spark Plugs in your boat?You fire up on the old spark plugs from the season before, the motor should have been %26quot;fogged%26quot; before it was winterized, burn the old oil out of the motor at start up (IT SMOKES), THEN replace the spark plugs, why foul up %26quot;NEW%26quot; plugs ? they should be changed every spring, changing over to %26quot;NEW%26quot; spark plugs makes a world of difference on an outboard motor, don't forget, it burns %26quot;MIX%26quot;, not straight gasoline like a car (if it's a 2 stroke outboard), so they get dirtier faster than a car's spark plugs.How often do you change Spark Plugs in your boat?I change them at least every 100 hours and clean them at least once a year.How often do you change Spark Plugs in your boat?Just do it every year when it comes out of storage, they are cheap.
How do I change the spark plugs in my 2002 Chevy Trailblazer?
My boyfriend and i would like to change the spark plugs our self and I was just wondering where they are locatedHow do I change the spark plugs in my 2002 Chevy Trailblazer?you never mentioned the engine size.
The inline 5cyl and 6cyl engines have the spark plugs located on the valve cover....UNDERNEATH the coils. This is a coil-on-plug system.......one coil per spark plug.How do I change the spark plugs in my 2002 Chevy Trailblazer?You should have 4 or 6 spark plugs in your vehicle depending on how many cylinders you have. Assuming you have a 6 cylinder, there should be 6 black that a visable as soon as you open your hood. At one end of them they should connect to what's called your distributer cap, which distibutes the spark. Follow those wires to the other end and they should run to your block, which houses your 6 cylinders, or 4. Where the wires meet your block, if you just pull them off the block your plugs should be right under them. If you already have the new ones, you just simply remove the old ones, pop in the new ones and place the wires back on. Now if your replacing the plugs because they are old you might want to replace those wires going to them, as well as on the the other side of the wires, your distributer cap. This will ensure a great start up, especially in the winter.How do I change the spark plugs in my 2002 Chevy Trailblazer?Best way to go is to buy a manual from your local auto parts store for 13 bucks along with some spark plugs for that particular year and model, then head home and read up on it first..the manual will expain step by step how to go about it.
Sometimes you need to use a dielectric grease on the plug wires.
The plugs need to be set at a certain gap setting.
They need to be tightened to a specific tourq.
Plus possibly more, depending on the year, make and model.
Dont be discouraged, there are just alot of details, Hope this helps.
The inline 5cyl and 6cyl engines have the spark plugs located on the valve cover....UNDERNEATH the coils. This is a coil-on-plug system.......one coil per spark plug.How do I change the spark plugs in my 2002 Chevy Trailblazer?You should have 4 or 6 spark plugs in your vehicle depending on how many cylinders you have. Assuming you have a 6 cylinder, there should be 6 black that a visable as soon as you open your hood. At one end of them they should connect to what's called your distributer cap, which distibutes the spark. Follow those wires to the other end and they should run to your block, which houses your 6 cylinders, or 4. Where the wires meet your block, if you just pull them off the block your plugs should be right under them. If you already have the new ones, you just simply remove the old ones, pop in the new ones and place the wires back on. Now if your replacing the plugs because they are old you might want to replace those wires going to them, as well as on the the other side of the wires, your distributer cap. This will ensure a great start up, especially in the winter.How do I change the spark plugs in my 2002 Chevy Trailblazer?Best way to go is to buy a manual from your local auto parts store for 13 bucks along with some spark plugs for that particular year and model, then head home and read up on it first..the manual will expain step by step how to go about it.
Sometimes you need to use a dielectric grease on the plug wires.
The plugs need to be set at a certain gap setting.
They need to be tightened to a specific tourq.
Plus possibly more, depending on the year, make and model.
Dont be discouraged, there are just alot of details, Hope this helps.
Do high end spark plugs really do all that much? And if so how do I determine the right plug for my car?
Currently, I have an 2006 Acura TSX. All I have in it is a cold air intake and just wanted to increase my gas millage and off the start push. I've done some of my own research and found some arguments over the fact that spark plugs do improve performance, and other claims that it doesn't do anything. If anyone has any knowledge on the subject it would very much appreciated for your help.Do high end spark plugs really do all that much? And if so how do I determine the right plug for my car?The ignition on your car will provide plenty of spark to fully burn the fuel with standard plugs. There is some benefit as far as lifespan of the plugs to go with the platinum version of the standard plug. All other %26quot;gimmick%26quot; plug claims are BS with modern electronic ignitions like yours.Do high end spark plugs really do all that much? And if so how do I determine the right plug for my car?Most autoparts stores will have a catalog to tell you which plugs can fit your car. I doubt it will make a noticeable difference off the line but the high end plugs usually require less regapping and cleaning.Do high end spark plugs really do all that much? And if so how do I determine the right plug for my car?Go with OEM plugs and you can't go wrong.Do high end spark plugs really do all that much? And if so how do I determine the right plug for my car?Platinum plugs will defiantly last longer. but with your 06 model I can't imagine them being bad yet. If your engine is running clean they should last 100,000 miles. The car manufacturers pay techs allot of money to design these engines from the factory. I suspect they know more about what kind of spark plugs goes in your vehicle than some kid behind a parts counter. :)How do you get your blankets clean hair tips
How much should it cost to replace the spark plugs on a 2004 Lincoln Aviator?
Vehicle diagnosis was that bad plugs were the reason for misfiring on 3 cylinders. Vehicle has 41000 miles on plugs. Quoate from dealer was almost $350 to replace plugs?? Seems high for eight $6.00 spark plugs unless I am missing something??How much should it cost to replace the spark plugs on a 2004 Lincoln Aviator?I am skeptical about the spark plug diagnosis. 41K is too soon to have no less that 3 plugs fail. If they are merely going by three different P030X (X would be the number of the cylinder misfiring) code to condemn plugs, they are not doing their job. If they use a scope to measure primary and secondary voltages, then they'd know 100% that it's plugs
I hope you didnt have to pay for that diagnosis, because I am fairly sure it is wrong. This code means more than simply bad plugs.
Possible causes for P030X codes:
Faulty spark plug or wire
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector
Burned exhaust valve
Faulty catalytic converter(s)
Running out of fuel
Poor compression
Defective computer
There is also a TSB (technical service bulletin) out on 04 Aviators for vehicles with those misfire codes. Have the dealer check for:
TSB No.: 06513
NHTSA No.: 10019912
TSB Date: January 1, 2006
Failing Component:
Engine And Engine Cooling:Engine
Description of Summary:
Engine misfire with diagnostic trouble code (dtc) pewee, p0302, p0303, p0304, p0305, p0306, p0307, p0308, and p0316.
If they wont, then go to another dealer.
Hope this helpsHow much should it cost to replace the spark plugs on a 2004 Lincoln Aviator?350?!?!?!? Spark plugs are 2$ a piece at checker. Replace them your self, its easy.
They must have wanted to change the plugs, wires cap and rotor.. and something else. that still doesnt seem worth 350$.. at all...How much should it cost to replace the spark plugs on a 2004 Lincoln Aviator?may be you need a coil to its mainly labor thats why your plugs run high cuz there platuim plugs they they should be good for 75000 miles but its labor lots of work to get to the plugsHow much should it cost to replace the spark plugs on a 2004 Lincoln Aviator?labor and labor. for a quote that high they don't want to do the job. all so go to some other shop that has a good rep and get a quote from them . you will be freaked at $$$$$$$$$$$$$ differentsHow much should it cost to replace the spark plugs on a 2004 Lincoln Aviator?they charge by the hour labor rate is high just check with another garage and get another estimate but you should be concerned about why the plugs are bad they are 100,000 mile plugs so they shouldn't be bad. and the warranty is still on the vehicle so you need to say to the dealership hey there is something wrong if this vehicle needs plugs because they are 100,000 mile plugs and try to get them replaced under your factory bumper to bumper warranty.
I hope you didnt have to pay for that diagnosis, because I am fairly sure it is wrong. This code means more than simply bad plugs.
Possible causes for P030X codes:
Faulty spark plug or wire
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector
Burned exhaust valve
Faulty catalytic converter(s)
Running out of fuel
Poor compression
Defective computer
There is also a TSB (technical service bulletin) out on 04 Aviators for vehicles with those misfire codes. Have the dealer check for:
TSB No.: 06513
NHTSA No.: 10019912
TSB Date: January 1, 2006
Failing Component:
Engine And Engine Cooling:Engine
Description of Summary:
Engine misfire with diagnostic trouble code (dtc) pewee, p0302, p0303, p0304, p0305, p0306, p0307, p0308, and p0316.
If they wont, then go to another dealer.
Hope this helpsHow much should it cost to replace the spark plugs on a 2004 Lincoln Aviator?350?!?!?!? Spark plugs are 2$ a piece at checker. Replace them your self, its easy.
They must have wanted to change the plugs, wires cap and rotor.. and something else. that still doesnt seem worth 350$.. at all...How much should it cost to replace the spark plugs on a 2004 Lincoln Aviator?may be you need a coil to its mainly labor thats why your plugs run high cuz there platuim plugs they they should be good for 75000 miles but its labor lots of work to get to the plugsHow much should it cost to replace the spark plugs on a 2004 Lincoln Aviator?labor and labor. for a quote that high they don't want to do the job. all so go to some other shop that has a good rep and get a quote from them . you will be freaked at $$$$$$$$$$$$$ differentsHow much should it cost to replace the spark plugs on a 2004 Lincoln Aviator?they charge by the hour labor rate is high just check with another garage and get another estimate but you should be concerned about why the plugs are bad they are 100,000 mile plugs so they shouldn't be bad. and the warranty is still on the vehicle so you need to say to the dealership hey there is something wrong if this vehicle needs plugs because they are 100,000 mile plugs and try to get them replaced under your factory bumper to bumper warranty.
How do you get access to EGR valve and backside spark plugs in 2006 dodge caravan?
Anybody familiar with grand caravans? theres an EGR valve bottom bolt that is impossible to get to.
Same with the spark plugs on the backside. Cant get to them without removing ...i dont know.. the whole engine? Didn't think these two jobs were going to be difficult.
Any help greatly appreciated. Thanks.How do you get access to EGR valve and backside spark plugs in 2006 dodge caravan?Try removing the wiper assembly box, remove plastic cowl just below windshield and wiper arms, the screws are a 25mm torx.Remove plastic covers to lower part of wiper arm. Wiper arms have a 15mm bolt, remove bolt then remove wiper arms a slight jiggle-twist motion, if stuck use small puller. Undo wiper harness connector on side of wiper box then take off the 13mm bolts holing box to body. Undo two drain hoses just under wiper box and pull it up and out as an assembly. Now you will have room to work on this car. it is fairly easy to do and make this tune up easier and access to EGR bolts.How do you get access to EGR valve and backside spark plugs in 2006 dodge caravan?Try using an extension with a flex head ratchet or two extentions with a swival joint in the middle
Same with the spark plugs on the backside. Cant get to them without removing ...i dont know.. the whole engine? Didn't think these two jobs were going to be difficult.
Any help greatly appreciated. Thanks.How do you get access to EGR valve and backside spark plugs in 2006 dodge caravan?Try removing the wiper assembly box, remove plastic cowl just below windshield and wiper arms, the screws are a 25mm torx.Remove plastic covers to lower part of wiper arm. Wiper arms have a 15mm bolt, remove bolt then remove wiper arms a slight jiggle-twist motion, if stuck use small puller. Undo wiper harness connector on side of wiper box then take off the 13mm bolts holing box to body. Undo two drain hoses just under wiper box and pull it up and out as an assembly. Now you will have room to work on this car. it is fairly easy to do and make this tune up easier and access to EGR bolts.How do you get access to EGR valve and backside spark plugs in 2006 dodge caravan?Try using an extension with a flex head ratchet or two extentions with a swival joint in the middle
How do you find out the right heat range for spark plugs for a 72 chevy 350 engine 120 psi of compression?
I'm having problems with it carbon fouling , loosing cylinders, rough idle in gear. Thinking it was a vacuum leak replaced the intake gasket and still having the problems. I'm thinking its either the spark plugs (R44T) or putting a hotter coil to fix the problem.
Before I go buy something I don't need , Can anybody help me please.How do you find out the right heat range for spark plugs for a 72 chevy 350 engine 120 psi of compression?If your plugs are carboning up you must not run the car very hard very often to keep the carbon from building up or your carburator needs attention such as it's too big for the engine or the jets need to be smaller in it as it sounds like it's getting too much gas, also check your plug wires for being bad and if you don't have a HEI distriburator in it and still have the old point distriburator get rid of it and put the HEI in it, any junkyard carries them and it will give you a lot hotter spark and you will never have to worry about changing points again and your engine timing will stay stable all the time.How do you find out the right heat range for spark plugs for a 72 chevy 350 engine 120 psi of compression?A sparkplug doesn't make heat, therefore it can't heat up the engine. Sparkplugs can not and will not make an engine run hot (or cold). The fire in the cylinder heats up the plug, not the other way around. Heat range simply means how hot the plug itself will be. If the plug is too cold, it won't be able to burn off the oil and fuel deposits that collect on it and it will foul. If it is too hot, the electrode can't cool fast enough and it may start to melt away. On high compression engines, there is more cylinder heat so a colder plug is usually used. Sometimes the heat on race engines is so great, even cold plugs melt-off the electrodes. This is a common problem when running nitrous oxide. Some top fuel engines don't even run electrodes. The ground electrode is simply cut-off and removed because it will melt-off! The spark from the magnetos on those kind of race engines has no problem at all jumping from the center electrode to the edge of the plug. The bottom line is, you want to run the hottest plug you can without melting the electrode. This just assures a clean plug that yields a good spark. Hope this helps.....How do you find out the right heat range for spark plugs for a 72 chevy 350 engine 120 psi of compression?120 lbs of compression is not that good. As for your question of heat range if you get a repair manual it will tell you what type of plug to use.How do you find out the right heat range for spark plugs for a 72 chevy 350 engine 120 psi of compression?Some good info on these links for proper plug heat range determination. Too cold of a plug will allow more fouling as will an overly rich carb adjustment or settings. Too hot can cause problems also. Stock engine? call a Chev dealer or parts store for what is normal plug for it....usually, you can go one size hotter with no problem. as in, R44T to R45T. Are you sure it's carbon fouling and not oil?
http://www.centuryperformance.com/spark.
http://www.ngksparkplugs.com/techinfo/spHow do you find out the right heat range for spark plugs for a 72 chevy 350 engine 120 psi of compression?%26quot;Low Compression, Rebuild Time!%26quot;
Before I go buy something I don't need , Can anybody help me please.How do you find out the right heat range for spark plugs for a 72 chevy 350 engine 120 psi of compression?If your plugs are carboning up you must not run the car very hard very often to keep the carbon from building up or your carburator needs attention such as it's too big for the engine or the jets need to be smaller in it as it sounds like it's getting too much gas, also check your plug wires for being bad and if you don't have a HEI distriburator in it and still have the old point distriburator get rid of it and put the HEI in it, any junkyard carries them and it will give you a lot hotter spark and you will never have to worry about changing points again and your engine timing will stay stable all the time.How do you find out the right heat range for spark plugs for a 72 chevy 350 engine 120 psi of compression?A sparkplug doesn't make heat, therefore it can't heat up the engine. Sparkplugs can not and will not make an engine run hot (or cold). The fire in the cylinder heats up the plug, not the other way around. Heat range simply means how hot the plug itself will be. If the plug is too cold, it won't be able to burn off the oil and fuel deposits that collect on it and it will foul. If it is too hot, the electrode can't cool fast enough and it may start to melt away. On high compression engines, there is more cylinder heat so a colder plug is usually used. Sometimes the heat on race engines is so great, even cold plugs melt-off the electrodes. This is a common problem when running nitrous oxide. Some top fuel engines don't even run electrodes. The ground electrode is simply cut-off and removed because it will melt-off! The spark from the magnetos on those kind of race engines has no problem at all jumping from the center electrode to the edge of the plug. The bottom line is, you want to run the hottest plug you can without melting the electrode. This just assures a clean plug that yields a good spark. Hope this helps.....How do you find out the right heat range for spark plugs for a 72 chevy 350 engine 120 psi of compression?120 lbs of compression is not that good. As for your question of heat range if you get a repair manual it will tell you what type of plug to use.How do you find out the right heat range for spark plugs for a 72 chevy 350 engine 120 psi of compression?Some good info on these links for proper plug heat range determination. Too cold of a plug will allow more fouling as will an overly rich carb adjustment or settings. Too hot can cause problems also. Stock engine? call a Chev dealer or parts store for what is normal plug for it....usually, you can go one size hotter with no problem. as in, R44T to R45T. Are you sure it's carbon fouling and not oil?
http://www.centuryperformance.com/spark.
http://www.ngksparkplugs.com/techinfo/spHow do you find out the right heat range for spark plugs for a 72 chevy 350 engine 120 psi of compression?%26quot;Low Compression, Rebuild Time!%26quot;
How do you go about changing the spark plugs in a 2000 Yamaha V-Star 1100 classic?
I am having trouble locating the spark plugs in my motorcycle, if anyone has any info on how to do so or a link to a site with an image walkthrough that would be great.How do you go about changing the spark plugs in a 2000 Yamaha V-Star 1100 classic?The easy answer is that they are at the end of your spark plug wires.
As I recall, the plugs are not easy to access, and require a long socket, a swivel, an extension and ratchet to loosen the plugs, and a magnet to remove remove them.
Try contacting Star Riders Assoc. Those kinds of owners clubs are usually a wealth of info and tips.
http://www.star-riders.org/
As I recall, the plugs are not easy to access, and require a long socket, a swivel, an extension and ratchet to loosen the plugs, and a magnet to remove remove them.
Try contacting Star Riders Assoc. Those kinds of owners clubs are usually a wealth of info and tips.
http://www.star-riders.org/
Subscribe to:
Posts
(Atom)